0 Comment

Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. 10 Jan Thank you for choosing this Mitsubishi Inverter. This Instruction Manual ( basic) is intended for users who “just want to run the inverter”.

Author: Gardarn Meztizil
Country: Guinea
Language: English (Spanish)
Genre: Finance
Published (Last): 6 April 2017
Pages: 252
PDF File Size: 19.19 Mb
ePub File Size: 8.93 Mb
ISBN: 809-1-84663-263-5
Downloads: 64684
Price: Free* [*Free Regsitration Required]
Uploader: Nikojas

Phase sequence needs not to be matched. Page – Mitsubishi inverter protocol computer l Doing so will damage the inverter. Initial Setting Refer to Pr. To reinstall, fit the cover vfr the inverter along the guides.

Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller

Since voltages and currents in the primary and secondary side of the inverter include harmonics, different meters indicate different measured values. For power factor mitsubishi e700 vfd manual, install a reactor on the inverter input side or in the DC circuit. For write, set the data as a control input instruction. Page Communication operation and setting Parameter Communication procedure Data communication between the computer and inverter is made in the following procedure: When the setting dial and key operation is made invalid, “HOLD” appears on the operation panel while pressing a key.

Main circuit connection Wiring Total wiring length The maximum possible length of the motor cables depends on the capacity of the mitsubishi e700 vfd manual and the selected carrier frequency. Do not connect a mechanical brake. Output is not shutoff. Operation Display Turn the digital dial until P. Frequency setting by analog input terminal 2, 4 Parameter Refer to the following table and set Pr. Operation mitsubishi e700 vfd manual Operation Function Description Used to change the frequency setting and parameter values.

Check if the RY signal mitsubsihi output after powering on the inverter. Fr-a7np series inverter plug-in option e kit profibus-dp communication function 89 pages. Refer to section Setting this parameter increases the magnitude of frequency e7000 changes according to the rotated amount of the setting dial, improving operability. Reset method of protective function Troubleshooting Reset method of protective function Eliminate mitsubishi e700 vfd manual cause of the error before you reset the inverter.

Failure to observe this could lead to injuries.


Offline Kitsubishi Tuning mitsubishi e700 vfd manual. Load Pattern Selection pr. When multiple motors are operated by a single inverter, protection cannot be provided by the electronic thermal relay function. Page If vibration becomes large by increasing the Pr. Page Signal Signal tion Tab.

Any equipment placed above the inverter should be heat resistant. PU operation mode Mitsubishi e700 vfd manual settings Change the acceleration time using Pr. Mitsubishi e700 vfd manual The used input signal terminal changes depending on the Pr. From the operation panel Disabled From communication communication option Communication frequency setting Connection of communication option command sending Refer to the corresponding commu- Pr. For the Y12 signal, set “12 positive logic or negative logic ” in Pr.

Page Mitsubishi e700 vfd manual setting by analog input terminal 2, 4 Parameter Perform operation by analog input current When the pressure or temperature is controlled constant by a fan, pump, etc. Motor brake and stop operation Parameter With brake opening completion signal input Pr. General flowchart NOTES Always set the communication check time interval before starting operation to prevent haz- ardous conditions. Removal of the fan cover Disconnect the fan connector.

Rs Communication PU connector Wiring 3. PU connector Wiring 3. When the initial value Pr.

A special motor cannot be protected by the electronic thermal relay function. Page Adjust the output torque current of the motor Parameter Selection method of general-purpose magnetic flux vector control Perform secure wiring.

Page Selection and protection of mitsubishi e700 vfd manual motor Parameter Before performing offline auto tuning Mitsubishi e700 vfd manual the following mirsubishi performing offline auto tuning. Simple mode parameter list Basic settings Operation Display Screen at powering on The monitor display appears. Avoid unnecessary reset and power-off.

By turning the digital dial, you can read another parameter. The ambient temperature should be as low as pos- since an in-rush current flows in the sible within the permissible range. Maintenance Timer Alarm pr. Page Frequency setting by analog input terminal 2, 4 Parameter 3.

Mitsubishi Electric FR-E700 Instruction Manual

If the frequency search result exceeds the set frequency, the output frequency is limited at the set frequency. Peripheral Devices When the breaker on the inverter primary side trips, check for the mitsubishi e700 vfd manual fault short circuitdamage to internal parts of mitsuubishi mitsubishi e700 vfd manual, etc. Page If the Pr. Page RES signal or by switching power off. Initial Setting Refer to E70 Page Stall prevention operation during acceleration may increase the acceleration time.

Operation Mode At Power On pr.